Semi-Automatic Metal-Cutting Bandsaws
A semi-automatic bandsaw runs the cut for you once you press start, so there's less work than on a manual saw. You still load the material and start each cycle. BTH carries eleven MACC semi-automatics, from the Special 320 M/S and 335 M/S through the 391 SV, 391 SVG and 411 M/S to the large DI and GA models.
MACC bandsaws are made in Italy and priced in Canadian dollars. Every saw in this collection runs on 460 V three-phase with a BTH-supplied transformer to suit your shop.
How the semi-automatic cycle works
On the M/S and SV models, press the start button and the saw runs the cycle: the vice closes and the band motor starts, the bow comes down through the cut and returns to its start position, the band motor stops and the vice opens. Most models also let you run a cut manually.
Compare the semi-automatic saws
Start with your largest section and the angles you cut. Round-tube figures are at a straight cut; each saw's page has its full table by angle.
| Model | Round tube, straight | Mitre range | Choose this when |
|---|---|---|---|
| 320 M/S | 230 mm (9.1 in) | 0° to 60° right | You want the start-button cycle on sections up to 230 mm. |
| 335 M/S | 260 mm (10.2 in) | 45° left to 60° right | You want the cycle run for you and mitres both ways. |
| 391 SV | 300 mm (11.8 in) | Straight-cut figures only | You cut big tube straight and want a simple start-button saw. |
| 391 SVG | 300 mm (11.8 in) | 0° to 45° right | You want a speed variator as standard. |
| 411 M/S | 300 mm (11.8 in) | 45° left to 60° right | You need 300 mm tube and mitres both ways. |
| 415 DI | 350 mm (13.8 in) | 60° left to 60° right | You mitre to 60° both ways and want an inverter blade drive. |
| 420 DI | 390 mm (15.4 in) | 60° left to 60° right | You need more room than the 415 DI. |
| 650 DI | 460 mm (18.1 in) | 60° left to 60° right | You cut large sections and mitre to 60° both ways. |
| 700 | 525 mm (20.7 in) | Straight-cut figures only | You cut very large sections straight, on a twin-column saw. |
| 700 DI | 525 mm (20.7 in) | 60° left to 45° right | You need twin-column capacity with mitres. |
| 702 GA | 550 mm (21.7 in) | 60° left to 45° right, programmed | You want the saw to set programmed mitre angles. |
Millimetres are MACC's figures. Inches are conversions, rounded to one decimal.
Manual, semi-automatic or fully automatic
- Manual bandsaws: you run the cut yourself, and on CSO models a hydraulic cylinder controls the bow's descent. Full control, suited to lower volumes.
- Semi-automatic (this collection): the saw runs each cut cycle; you load the material and start each cut.
- Fully automatic bandsaws: the saw also feeds the material and repeats the cycle.
Owning a semi-automatic MACC in Canada
Our semi-automatic saws come with a 12-month warranty, and their parts and blades are kept here in Canada. When service is needed, we send our own technician; if we can't, we'll find a local technician near you who can do warranty-approved work. Training is available, installation is available on request, and financing is available if you ask us.
Not sure which size you need? Email sales@bthsales.ca or call 519-461-1381 and tell us what you cut. We're MACC's exclusive Canadian importer, a family-owned team in St. Marys, Ontario, in business since 2001. Ships across Canada from St. Marys, ON. Orders ship promptly once confirmed, and we'll send tracking when it leaves.
Frequently Asked Questions
What does a semi-automatic bandsaw do that a manual saw does not?
On the M/S and SV models, you press the start button and the saw closes the vice, starts the band motor, lowers the bow through the cut, returns the bow, stops the band motor and opens the vice. On a manual saw, you run the cut yourself. Most semi-automatic models also let you run a cut manually.
When should I choose a fully automatic bandsaw instead?
Choose fully automatic when you cut many pieces to length. MACC's fully automatic models feed the material, clamp, cut and repeat the cycle on their own, so you don't have to start each cut.
How do I compare capacities between models?
Each saw's page shows MACC's maximum cutting capacity table in metric and imperial for round, square and rectangular sections at each mitre angle. For example, the Special 320 M/S takes round tube up to 230 mm (9.1 in) at a straight cut. Check your largest section at the angle you need.
Is training available on the semi-automatic cycle?
Training is available on each semi-automatic saw, and installation can be arranged on request.